Reddit refuge, escentric engineer and serial hobbyist.
So you have photoprism pointed to a folder but you push photos into the folder witb syncthing. How do you trigger the re-index or its somehow automatic? I run my photoprism in docker and I always had to manually trigger the index after changes to the folder.
As someone who has and still used photoprism for over two years and donated heavily…steer clear. Their update cycle is slow and the things they keep adding don’t seem helpful. Still no multi-user support. If you don’t upload new photos via photoprism using WebDAV you have to make your own scripts to watch for changes and refresh which took a lot of time for me to setup.
I’m just going to start using Nextcloud and Memories app going forward.
Most folks ignore laptops, but if you’re OK with USB storage or getting the special caddy to install the internal 2.5" drive you can get great deals on laptops. This one idles around 4W with the screen off.
Install Enocean wireless, battery free switches. I’ve used them for many years, they work awsome. The switches can go anywhere you want (double side tape on any surface) or screw in as normal light switches. The act of pushing the button generates enough energy to send the RF signal to a receiver you install with the light and its powered from AC mains.
Been using it for over a year on two 8tb SSDs in strip and 14tb as mirror. This is on Debian and its flawless and wonderful. I run btrkbk hourly for snapshots, backups to remote locations and house keeping with 6 months of hourly snaps. Life is great.
I have the micro form factor I assume the same as you. Basically just a laptop in a small desktop case. I never installed tlp I’ll have to give that a shot but I’m pretty sure it’s optimized. I have two as servers and one as a router and I’d love to get it down to 12w total! I monitor the whole server rack with an iotawatt and all my servers and networking gear hovers around 75w idle.
I’d question that. I have three 3080 and they’re consistently about 8W each with one ssd and onboard graphics. I even went so far to splice three barrel jacks to a single 60w power supply that powers all three to avoid the losses of an additional 2 power supplies and this gets me the 8w idle power with Debian and throttling.
At the risk of sounding like an oaf I just use an excel document, and these days I just keep it in nextcloud and edit it via a browser while in the driveway. Each car gets a sheet. Keeping it simple.
I have so much trash on my network. For instance my security cameras are decentralized and we use tinycam on android to view them so I had to allow an exception for rtsp to get between the dirty iot WiFi and our normal WiFi. Our WiFi connected Bose speakers and Spotify is also another set of annoyance, they will only work if you try to connect to them from the same subnet via Spotify and app. I’ve tried to NAT the traffic and it didn’t work.
It’s going to haunt you for years. Wife: “why doesn’t this iot thing work?” Oh its on the wrong network. “I don’t understand it just doesn’t work”. Then I go add more exceptions in pfsense and the cycle continues.
Bought one, thank you!
Bingo. I’ve grown these before and they get hints of red at the top of the bell only when they get enough light. I think it’s light deprived but still looks very healthy.
Ditto, though I’m getting more and more resentful by the day at the lack of multi user support. I’m not going to donate to them again.
Blackvue cameras have WiFi but its always off by default. You have to manually toggle it with a button and if nothing connects it turns back off.
Too much steroids and coke
I hear ya but my instance is old (before i knew docker) and just works on the rails. I also tweak the heck out of it for performance so I deal with the annoyance once every two years. If it completely blows up I might roll it on docker.
I understand that everyone doesn’t always have a perfect experience but I’ve been using the same instance of nextcloud for over 8 years I just keep upgrading and migrating. It just works. Only issues I’ve had is when Debian withholds updating php for too long or when they finally do all the config files for php get fucked and I have to redo them all.
Burning natural gas isn’t so awful but getting it out of the ground and to the place where is needs to be burned is always overlooked. It’s a gas, it wants to escape and much of the infrastructure leaks and so a great deal is lost before its used. I walk around Boston and no joke you just SMELL it all the time because the infrastructure is so old. Natural gas is also mostly methane which when leaked is 80 times more potent than CO2. Furthermore much natural gas needs to be transported on ships to be uses. To summarize there is no ‘greener’ fossil fuels it’s all to be avoided if possible.
Here is the list!
1 x Samsung SSD 980 1TB
1 x Adata XPG SX8200 Pro 2TB
2 x Samsung SSD 870 QVO 8TB
1 x Western digital engineering sample. Cannot comment. 4TB
1 x Seagate Exos X16 14tb
I bought all the gear to do 10gbe but ultimately went back to 1gig simply because the power consumption. The switch alone used 20w at idle and each NIC burned 8w and I couldn’t justify it.